Mauch - PL 2-6S / 4-6S BEC

ab 62,55 €
inkl. 19% USt. , zzgl. Versand
  • Battery Eliminator Circuit für Pixhawk
  • Input: 2-6S
  • Ausgangsspannung 5 - 12V (siehe Optionen)
  • Ausgangsstrom 1 - 3A (siehe Optionen)

Bitte Kabel für Pixhawk 2.1 zusätzlich kaufen


  • Wählen Sie eine Option 

Dieser Artikel hat Variationen. Wählen Sie bitte die gewünschte Variation aus.

Sofort verfügbar

General

The new PL - Series BEC's are an improved design from the HS 2-6S BEC, with the following changes:

  • The BEC power supply is no more passed trough the sensor board and connects directly to the flight controller.
  • Bright blue "power on" LED.
  • Connection port for PL-xxx sensor board or PL - Sensor Hub X2/X8 with 5.0V / 0.5A
  • External connections via Molex Clik-Mate / 1.25mm connectors. (50238)
  • The BEC measures the output current and increases the output voltage by a few millivolt depend on the output load. This compensates the voltage drop in the connection from BEC to FC and to the receiver. To keep the voltage more stable.
  • Delivery inclusive CFK enclosure.

In the box - dependent on option

PL 2-6S / 1x:

  • 1x PL-2-6S BEC 1x5.3V / 3A
  • 1x CFK enclosure
  • 1x Sensor cable (040) Molex Clik-Mate 4p / L = 150mm

 

PL 2-6S / 2x:

  • 1x PL-2-6S BEC 2x5.3V / 3A
  • 1x CFK enclosure
  • 1x Sensor cable (040) Molex Clik-Mate 4p / L = 150mm
  • 1x Backup cable (050) for Pixhawk 2.1 / Molex Clik-Mate 2.0-6p / L = 150mm

 

PL 4-6S / 3x:

  • 1x PL-4-6S BEC 2x5.3V / 3A + 1x 12.0V / 3A
  • 1x CFK enclosure
  • 1x Sensor cable (040) Molex Clik-Mate 4p / L = 150mm
  • 1x Backup cable (050) for Pixhawk 2.1 / Molex Clik-Mate 2.0-6p / L = 150mm
  • 1x 12.0V output cable one site Molex Clik-Mate 1.25mm-4p, the other site open. / L = 150mm

 

The PL - BEC's are delivered without FC cable, so please purchase the correct cable to match your setup:

041: DF13-6p -> Pixhawk 1 / APM... etc.

042: Molex Clik-Mate 2.0 - 6p -> Pixhawk 2.1

043: JST-GH-6p -> Pixhawk 3... etc

Installation:

Please connect the minus (black) wire of the PL - BEC as close as possible to the main battery, as he is the ground reference for the voltage measurement. The positive wire (red) can be connected to the PDB.
The PL - BEC's can be screwed down to the main frame, by removing the 4 bottom M3 screws and drilling holes into the frame. Then reinstall the screws trough the frame.

PL 2-6S / 1x: 36mm x 24mm x 10mm DXF file / PL 2-6S / 1x

PL 2-6S / 2x: 34mm x 38mm x 10mm DXF file / PL 2-6S / 2x

PL 4-6S / 3x: 34mm x 52mm x 10mm DXF file / PL 4-6S / 3x

Hersteller: Mauch
Artikelnummer: 316
GTIN: 4251935112672

0

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufentscheidung:

Kontaktdaten
Frage zum Artikel